歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

安裝超聲波清洗機需要留意一些什么呢？

作者：admin來源：http://m.dijiushangdian.cn/時間：2021-03-08

超聲波清洗是一種非常的清洗方法，特別適合當今高度發達的社會，可以用于各個領域。但是超聲波清洗機本身非常準確，安裝過程必須按照規格進行，耐心完成所有必要的工作，確保設備達到預期的效果。特別是超聲波清洗機的安裝預防措施包括以下幾個方面。

Ultrasonic cleaning is a very advanced cleaning method, especially suitable for today's highly developed society, can be used in various fields. But the ultrasonic cleaning machine itself is very accurate, the installation process must be carried out according to the specifications, patiently complete all the necessary work, to ensure that the equipment achieves the desired effect. In particular, the installation precautions of ultrasonic cleaning machine include the following aspects.

一，重點是準備工作和噴砂處理。

1、 The emphasis is on Preparation and sandblasting.

在正式安裝超聲波清洗機之前，必須準備一種與超聲波交換器(包括正確的)粘合的粘合劑。同時，超聲波清洗機制造商必須停止超聲波轉換器和所需膠水的圓筒，停止噴砂。(威廉莎士比亞、超聲波清洗機、超聲波清洗機、超聲波清洗機、超聲波清洗機)噴砂接頭必須符合要求，噴砂要求為鉆石砂。對沙子的要求比較高。要慎重選擇，要打孔等。噴灑沙子時壓縮空氣的壓力必須調整以符合規定的要求，由空氣源處理器除濕的高壓空氣。

Before the installation of the ultrasonic cleaning machine, an adhesive must be prepared to adhere to the ultrasonic exchanger (including the correct one). At the same time, the ultrasonic cleaning machine manufacturer must stop the ultrasonic converter and the required glue cylinder, stop sandblasting. (William Shakespeare, ultrasonic cleaning machine, ultrasonic cleaning machine, ultrasonic cleaning machine, ultrasonic cleaning machine) the sandblasting joint must meet the requirements, and the sandblasting requirement is diamond sand. The demand for sand is relatively high. We should choose carefully and punch holes. When spraying sand, the pressure of compressed air must be adjusted to meet the specified requirements, and the high-pressure air dehumidified by the air source processor.

二，注意相關清潔工作。

2、 Pay attention to relevant cleaning work.

據超聲波清洗設備制造商透露，蛇毒和超聲波交換器首先需要停止清洗，后者需要應用準備好的溶液進行清洗，去除基本表面的一些污垢，然后進行清洗工作。(威廉莎士比亞、超聲波、超聲波、超聲波、超聲波、超聲波、超聲波、超聲波)同時，超聲波清洗機的汽缸需要連續清洗多次。干燥后接受特殊溶液，停一下。網眼墊的厚度應滿足要求，不銹鋼網要清潔干凈。

According to the manufacturer of ultrasonic cleaning equipment, the snake venom and ultrasonic exchanger need to stop cleaning first, and the latter needs to use the prepared solution to clean, remove some dirt on the most basic surface, and then carry out the cleaning work. (William Shakespeare, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic) at the same time, the cylinder of the ultrasonic cleaning machine needs to be cleaned continuously for many times. After drying, accept the special solution and stop. The thickness of mesh pad should meet the requirements, and the stainless steel mesh should be clean.

三，注意干燥、預熱處理。

3、 Pay attention to drying and preheating.

清潔的超聲波轉換器、氣瓶和網墊必須放入烤箱以停止干燥。干燥溫度也要控制在該范圍內。然后在干燥2小時后冷卻到一定溫度時要停止。超聲波清洗機公司介紹說，完成所有粘合劑準備任務后，注意粘合劑(常溫)，停止繼續粘合劑。

Clean ultrasonic transducers, cylinders and mesh mats must be placed in the oven to stop drying. The drying temperature should also be controlled in this range. Then, after drying for 2 hours and cooling to a certain temperature, it should be stopped. Ultrasonic cleaning machine company said that after completing all the adhesive preparation tasks, pay attention to the adhesive (room temperature), stop adhesive.

上一篇：超聲波生產廠家講解清洗機會損壞清洗物嗎？
下一篇：超聲波零部件清洗機的五大特點之詳細闡述